Protos 700X:. Here's a tutorial video showing how to set up the MSH iKON Flybarless unit, followed by the first two test flights. Great FBL unit! Skip navigation. How to set up iKON FBL Unit. ![]() ![]() App for iOS tablets and phones. It allows to set parameters and settings on Brain/Ikon/Xbar/Tracx flybarless controllers. This App needs latest firmware release on the unit to be used to its full potential. If your devices has internet access, the app will prompt you in case a new firmware for the flybarless unit is available. App is supported natively by Flybarless units with code MSH51630 and MSH51632, all other units type need BT module MSH51610, sold separately. Call of duty modern warfare 2 torrent download razor1911 password windows 7. MSH products can be purchased in any of the official MSH dealer shop. • Only on iX12 Spektrum transmitter with actual iX12 firmware, during the changes of values with Integration some random symbols are displayed on screen (EG: “???”): Patched • When Jeti protocol is used, some fake “Elevator sensor out of range” appear in the events. Fake events eliminated • Only using Futaba S.Bus2 protocol, only using Castle Creation ESC and only when Live Link is active in the ESC, some tail kicks happen, solved • The MIN, MAX, AVG values of parameter 10 of the logs when zoomed don’t correspond to the displayed zoomed graphics but to the values of the full graphics. 3.2.000 (firmware 3.2.000) • Added management of the telemetry of new YGE *VT ESC's • Implemented the changed (from Kontronik before the imminent release) Kontronik ESC protocol • Added for Nitro/Gasser, the management of telemetry log and transmission of a digital temperature sensor (Jeti: MT300EX, Futaba: SBS-01T) with sensor signal connected on CH5 and powered from an 'Y'. Work for ALL protocol selected (with Futaba S.Bus2 receivers the Futaba temperature sensor can be directly connected on the S.Bus2) • Added Multiplex MSP telemetry. 3.1.027 (firmware 3.1.027) • Added telemetry for Kosmik, Jive Pro, Kolibri, Kontrol-X ESC's. Is needed a new firmware release for the ESC not yet released from Kontronik, and a cable with the 5 pole kontronik connector • Added for OpenTX Transmitters and FrSky receivers with Smart Port the Brain2 telemetry transmission of ESC data's (is needed a special cable adapter) • Added in Governor pages (Wizard & Advanced) the “mAh Max Usable”. If ESC telemetry and governor are either active and the 'Battery Used mAh' value raise this new tunable value (mAh Max Usable), the pilot is advised by a RPM reduction of ~20%. 3.0.022 (firmware 3.0.022) - Fixed the Bluetooth problem that don't work if S.Bus/S.Bus2 protocol is selected - Improved the speed of S.Bus decoding routine. Now less latency - Improved the speed of updating channel signal to Brain functions (for all kind of receiver) - Improved the speed of serial interface (for either 'Serial USB' or Bluetooth) - Now Brain Governor engage when Motor reaches the 50% of the target speed instead of the precedent 56% percentage - Now when a servo output is reversed (in wizard panel 7/8 or in Advanced->Servos), the positive and negative servo limits are exchanged. Mainly to avoid mechanical binding when you reverse the Tail servo movements after the limit are done • Now with Jeti integration, when a servo output is reversed (in Common parameters->Servos), the positive and negative servo limits are exchanged. Mainly to avoid mechanical binding when you reverse the Tail servo movements after the limit are done (no new brain.bin needed) • For temperature values with Jeti telemetry, changing Celsius Fahrenheit in System ->Configuration->Temperature units, does not change anything: Fixed • In the software, improved the display update speed of the change of the parameters handled with potentiometers - New French resources - New Russian resources - Renamed the separated pdf instructions - Other small bug fixes and optimization/compression/reduction/speed up of the code • 3.0.020 Mar 6, 2017. 3.0.006 (Firmware 3.0.006) • In some particular condition the event logs hang and never recover. Fixed (the same condition could occur also with the fat of recorded Log) • For Hobbywing ESC (that don't send with telemetry the BEC voltage) the 'Servo Voltage' is recorded and transmitted like if it is the BEC voltage coming from esc - Like Logs that are stopped due to an app connection to the device, also timers and flight count are stopped and not incremented - For nitro when is required a throttle value for idle greather than actual raised from 10% to 20% the threshold of governor disengage and soft start engage. - Sometime some unit don't enter in check mode in panel 7 & 8.
0 Comments
Leave a Reply. |